MJT VTS Stratocaster - Nitro 2 Tone Sunburst Heavy Relic Finish (2020) - Sliders SRV 59' Pickups - AAAAA Flame Roasted Fender Maple Neck by Musikraft - Callaham Bridge w/ Brass Block - Vintage Spec - G&G Brown Strat Case
Dream guitar - the 2 Tone (pre 1957) Replica Strat! Premium parts and craftsmanship.
This listing is for a custom MJT Relic Stratocaster style guitar with a Fender neck by Musikraft. The guitar was designed to be as accurate as possible to an original 56' Strat...with a few modest upgrades...like a 5A flame neck :-). The body cavity has also been copper lined and tied to ground to keep any outside interference where it belongs....outside.
The neck is vintage spec with a compound radius. 5A Flame!
Rodney at Sliders, in my opinion, is the best there is when it comes to accurate vintage pickups. The SRV 59's that drive this guitar are well sought after. The bridge is the best - vintage spec - Callaham. The single ply pickguard is also Callaham. . Aged Kluson Tuners and guard shield, bone nut, pure vintage springs, alder body, roasted neck. Check this out!
MJT Aged Finishes (Carthage, MO) Nitro 2-tone Sunburst Body w/ Neck Relic - G&G OHSC with key.
Kluson tuners - aged by MJT
Botique - Sliders ’59 “SRV” - As real as it gets... A hotter wound pickup setup that mirrors SRV tone.
Musikraft / Fender Strat® Roasted AAAAA (that's 5) Flame maple neck - Stainless 6105 Frets - vintage spec w/ modern compound fret radius (see below for detail)
Callaham Vintage Style Cold Rolled Steel Bridge
Smokey B's - 54 Vintage accurate set up w/ CTS pots and repop "phonebook" tone cap. 3-way
Switchcraft selector switch.
Fender aged knobs.
"Pure Vintage" Tremolo Springs
"Pure Tone" multi-contact 1/4" output jack
Callaham 1-ply aged pick guard
Strat® Neck Custom Build Specs
Guitar Neck Build:Qty: 1
Construction Type:2 Piece Constructed
Orientation:Right for Right Handed Players
Scale Length:25.5" Standard Fender
Number of Frets:21
Nut Width:1 5/8 (41.28mm)
Nut Slot Style:1/8" Nut Slot (Standard Fender)
Heel Width and Type:2-3/16" (55.55mm) Rounded Strat
Truss Rod Type:Single Acting w/ Vintage Nut adjust @ Heel
Shaft Wood: Roasted Flame Maple 5A
Fingerboard Radius:Compound 7 1/4 to 9 1/2"
Fingerboard Edge Style: Heavy Rolled Fingerboard Edges
Tuner Hole Size:11/32" (Standard Kluson)
Top Inlay Type:1/4" Dots (black)
Side Markers:White 2mm
Side Dot Location:50/50 Split (Finger Board Wood and Shaftwood)
12th Dot Spacing:Wide (Vintage Style Pre 1964)
Fret Size and Type:6105 Stainless (Medium)
Back Profile Shape and Size:V-C 81 95
Neck Roasting Option: (Apply Roasting Service (Maple Woods Only))
Sliders Pickup Specs:
’59 “SRV”
Vintage 59’s
The 59′s are exact re-productions of Fender pickups produced in the late 50’s.
Throughout this period Strat pickups were built from similar materials and to the same basic specification, variation was mainly due to the differing batches of AlNiCo, coil wire and most importantly the individual operator that actually hand built the particular set. Around this time magnetic polarity went to South but retained the clockwise winding
My 59′s re-creates this general specification. I use my specially “Vintage Charged” AlNiCo 5 to replicate the very important, lower powered AlNiCo blends of the 50’s and 60’s.
59/SRV
The “59/SRV” re-creations are the same period correct 1959 set but given selected power adjusted AlNiCo and a small (secret) ”over wind” to nail Stevie’s power and warm/bluesy tones.
My 59/SRV ‘s are still a classic vintage voiced pickup, just tweaked a little to hit that clarity, warm up the tone and really drive that amp!
“Bakelite” style pickup covers, 6/32 UNC screws with amber rubber spacers.
At the end of the day all my pickups are totally vintage correct and as such, everything I make could have come from “back in the day”.
®Strat and Stratocaster and Fender are registered trademarks of Fender Musical Instruments, Inc.
In relic mint condition.
Thank you!
